N3 / #3 Nylon Zipper Chain Production Kit for Cushion & Pillow Cover Makers – 200 m / 656.17 ft + 400 Single-Pull Sliders ST-T5T-NAYLON-200M400K

Build zipper lengths around the real cover opening

Pillow covers and cushion covers are often made in multiple dimensions, fabrics and closure styles. A ready-made zipper may be too short, too long or unsuitable for the exact position of the opening.

This N3 / #3 nylon zipper chain production kit provides 200 m / 656.17 ft of continuous tape and 400 single-pull sliders. It is designed for home-decor makers, sewing studios, upholstery workshops and businesses producing repeated cover styles in more than one size.

Plan each zipper around the actual textile design

Measure the working zipper route from where the zipper begins operating to where it needs to stop. Do not use the full outside perimeter of a cover unless that complete edge is truly the zipper opening.

Account for seam allowance, piping, cover overlap, lining bulk, fabric thickness, corner turns and the final end finish. Placing the chain along the intended seam before cutting helps prevent a zipper that is too short or leaves unnecessary tape waste.

Why 400 sliders support multiple production runs

The included slider quantity gives workshops flexibility when several pillow or cushion-cover designs are being prepared in the same production cycle. The final number of completed covers depends on opening length, the number of sliders used per cover and the chosen end-finishing method.

Before starting a batch, record each cover style, zipper length, planned quantity, opening direction and slider requirement. This simple production list helps control tape use and reduces the risk of running short on moving zipper components during sewing.

Single-pull sliders for back-panel and one-side openings

Each supplied slider has one pull tab on one side of the slider body. This is practical for pillow and cushion covers normally opened from a rear panel or one main access side.

Single pull describes the pull-tab layout, not a one-direction zipper. When a cover requires comfortable access from both faces, choose a slider configuration that supports that handling requirement.

Test the chain-and-slider system before full production

Before preparing multiple cover zippers, install one slider on a short section of the supplied chain. The slider should move smoothly, close both sides evenly and leave no visible gap behind it.

A similar-looking chain from another zipper family may not use the same coil profile or slider channel. Testing the real chain-and-slider combination first is the most reliable way to reduce avoidable rework during production.

Choose a zipper type around the finished cover

This is an N3 / #3 nylon zipper-chain system. Where the zipper must disappear completely into the seam, an invisible zipper may be a better choice. Heavier covers, thick fabrics or wider zipper channels can also require another zipper construction.

Choose the zipper according to fabric thickness, cover construction, expected handling and the finished look—not only according to the visible zipper size.

Custom zipper-kit requests

For a custom zipper-set request, share the required tape length, tape color, slider configuration, estimated quantity and a sample or drawing of the final cover. These details help evaluate the suitable zipper-chain and slider arrangement for your production project.

Frequently Asked Questions

Can I cut the chain for different pillow-cover sizes?

Yes. This is continuous N3 / #3 zipper chain designed to be cut around the actual opening of each cover.

Are 400 sliders included?

Yes. The kit includes 400 single-pull sliders with 200 m / 656.17 ft of zipper chain.

Is this a complete ready-to-sew zipper?

No. The final zipper length, slider installation and end finish are prepared by the maker or workshop.

Can I use this for cushion-cover repairs?

It can be suitable when the existing zipper profile, sewing layout and intended use are compatible with N3 / #3 nylon zipper chain.

What does single pull mean?

It means the pull tab is located on one side of the slider body. It does not mean the zipper moves in only one direction.

Can I request a different tape color or kit arrangement?

Yes. Share the required tape length, color, slider style and estimated quantity so the suitable production-kit configuration can be evaluated.