#5 Nylon Zipper Chain Production Kit for Bag & Case Workshops – 200 m / 656.17 ft + 100 Single-Pull Sliders ST-T10T-NAYLON-200M100C

Build zipper runs around the actual bag or case opening

Ready-made zipper lengths do not always fit a bag, case, organizer or textile cover. Deep gussets, rounded corners, lining bulk, edge binding and reinforced sections can all change the real zipper route of the finished product.

This #5 nylon zipper chain production kit provides 200 m / 656.17 ft of continuous tape and 100 single-pull sliders. It is intended for bag makers, case repair shops, sewing studios and workshops that need a substantial zipper-chain supply for repeat work across multiple product sizes.

Who benefits from a 200-meter zipper-chain kit?

This quantity is suitable for businesses producing several bag, case or organizer models over time. It can support repeated cutting schedules without requiring the workshop to keep large numbers of ready-made zipper lengths in stock.

The total number of completed zipper runs depends on the length of each opening, the number of sliders used per item and the selected end-finishing method. Planning tape use and slider allocation together gives the workshop better control over production materials.

Measure the functional zipper route before cutting

Measure from the point where the zipper begins operating to the point where it needs to stop. Do not use the full outside edge of a bag or case unless that entire edge is the actual zipper path.

Account for seam allowance, lining thickness, gusset depth, edge binding, corner turns, zipper guards and the planned end finish. For repair work, test-fit the new zipper chain along the intended seam before cutting because old material may have stretched or shifted over time.

Single-pull sliders for one main access side

The included sliders have one pull tab on one side of the slider body. This arrangement suits closures normally opened from one main exterior face, including bag tops, case lids, organizer compartments and pouches.

Single pull describes the pull-tab layout, not the travel direction of the zipper. A product that requires comfortable access from both sides may need a different slider construction. Select the slider structure around actual handling, product orientation and opening design.

Test before preparing a full production batch

Before cutting multiple zipper lengths, install one included slider on a short chain sample. The slider should move smoothly, close both sides evenly and leave no visible gap behind it.

Once the chain-slider system is confirmed, create a production list that records each item’s zipper length, quantity, opening direction and slider requirement. This helps reduce cutting mistakes and shows whether separate slider stock may be needed for future production.

Installation checks for cleaner zipper performance

• Test one slider on a short zipper-chain sample before cutting final lengths.
• Keep both sides of the tape straight and evenly tensioned while sewing.
• Leave clearance around lining, binding, gussets and reinforcement layers.
• Confirm the intended opening direction before stitching the chain into the product.
• Finish both chain ends so the slider cannot leave the intended zipper route.

Choose the right zipper construction for the project

This is a standard #5 nylon zipper-chain system. Another construction may be needed when a project requires molded plastic teeth, metal teeth, TPU-coated tape, a smaller zipper profile or a finished zipper with a defined end type.

Choose the zipper according to the zipper-channel width, material thickness, expected opening frequency, product load and finished appearance. A visually similar zipper can still be unsuitable when its chain profile or slider configuration does not match the project.

Custom zipper requests

For custom zipper supply, provide the required chain length, zipper size, tape color, slider configuration, intended product type, estimated quantity and any reference sample. These details help match the zipper-chain kit to the actual bag, case or organizer project.

Frequently Asked Questions

Is this a finished zipper with ready-to-sew ends?

No. This is continuous #5 zipper chain. The final length, slider position and end finish are prepared by the maker or workshop.

Does the kit include sliders?

Yes. The kit includes 100 single-pull sliders with 200 m / 656.17 ft of zipper chain.

Can this kit be used for bag and case repairs?

It can be suitable when the original zipper profile, sewing layout and expected use are compatible with #5 nylon zipper chain. Test a short section before completing the repair.

What does single pull mean?

It means the pull tab is located on one side of the slider body. It does not mean the zipper can move in only one direction.

Does the kit include finished end stops?

The listed contents are zipper chain and sliders. The correct end finish depends on the construction of the final bag, case or cover.

How can I compare other zipper and slider options?

Use the Zipper Types and Models collection for zipper constructions and the Zipper Sliders collection for pull-tab styles and slider structures.